Cracking the jammer? We've already thought of everything you can think of
In major electronic forums and social platforms, there will always be posts of this kind explaining how to crack the signal jammer. Leaving aside what the purpose of cracking is, let's analyze whether these claims are effective.
Let's take a look at how a signal jammer works:
The jammer scans from the low-end frequency of the forward channel to the high-end frequency at a certain speed during operation. The scanning speed can cause garbled interference in the received message signal of the mobile communication (mobile phone), and the mobile communication (mobile phone) cannot detect the normal data sent from the base station, so that the mobile communication (mobile phone) cannot establish a connection with the base station. Mobile communication is manifested as search network, no signal, no service system and other phenomena.
Next, let's analyze the so-called method of cracking the signal jammer:
One of the ways to crack a signal jammer
Enter your mobile phone settings, click "Network Settings", change the network mode to "Manual Mode", then enter "Network Search", wait until the words "China Mobile" or "China Unicom" appear, then exit immediately. The mobile phone will have a signal, but the length of the anti-blocking time depends on the quality of the mobile phone. This method works for most mobile phones. Principle: The work of the mobile phone is originally within a certain frequency range. The mobile phone and the base station are connected by radio waves to complete the transmission of data and sound with a certain baud rate and modulation method. Then the jammer scans from the low-end frequency of the forward channel to the high-end frequency at a certain speed during the working process. The scanning speed can cause garbled interference in the message signal received by the mobile phone, and the mobile phone cannot detect the normal data sent from the base station, so that the mobile phone cannot establish a connection with the base station. The mobile phone manifests as the phenomenon of searching the network, no signal, no service system, etc.
from a forum
1. The method is invalid.
2. The principle of the shield is correct, but it may confuse the point of view intentionally or unintentionally. Fundamentally speaking, no matter what kind of mobile phone signal frequency, it exists within the shielding range of the signal jammer. The signal jammer is responsible for scanning and emitting the same frequency band. There is no such thing as a mobile phone with good quality. , so no matter how you switch, it will be blocked.
The second method of cracking the signal jammer
Because the working principle of the blocker is to block the mobile phone by interfering with the mobile phone signal in the specified band, as long as the receiving and transmitting frequency of the mobile phone is modified, it can be prevented from being blocked. The blocking device can only block the mobile phone signal of 900-1800MHZ, while the receiving and transmitting frequency of the mobile phone It is 850-1900MHZ, which is much larger than the shielding range of the shield, so as long as the receiving and transmitting frequency of the mobile phone is adjusted to the maximum in the mobile phone settings, the mobile phone signal can be received normally.
1. The method is invalid;
2. The signal blocker does not just block a single frequency band. Take Dazhan Electronics' new 5G signal jammer as an example, the frequency bands that can be shielded are as follows
No. Signal name Frequency band
1 CDMA, CDMA2000 870MHz-880MHz
2 GSM 925MHz-960MHz
3 GSM, FDD-LTE, TD-LTE 1805MHz-1920MHz
4 TD-SCDMA 2010MHz-2025MHz
5 WCDMA, CDMA2000, FDD-LTE 2110MHz-2175MHz
6 TD-LTE 2300MHz-2390MHz
7 WiFi, BLUETOOTH 2400MHz-2485MHz
8 TD-LTE, mobile 5G 2515MHz-2675MHz
9 Telecom 5G Unicom 5G 3400MHz-3600MHz
10 Mobile 5G 4800MHz-4900MHz
DZ-810M5G mobile phone signal jammer can block the frequency band
Of course, someone will definitely try to set their mobile phone frequency band outside this range, such as the neutral frequency band 2200-2300MHz, etc., but there is no operator's communication signal in these frequency bands, and a mobile phone set in this frequency band is a brick .
The third method of cracking the signal jammer
This method has relatively high requirements on the mobile phone and the environment, but the effect is also the best and the most concealed. The premise is that the mobile phone must have wifi wireless Internet access function and there must be an available wireless network around. After searching for and successfully connecting to an available wireless network with your mobile phone, you can still surf the Internet and do not use traffic even if the mobile phone has no signal.
1. The method is invalid;
2. When the mobile phone is within the shielding range of the signal blocker, the mobile phone cannot search for the wireless network. In fact, the frequency band of the wireless network is easily blocked. This point of view is equivalent to sometimes we forget to bring the key when we go out: the lock is on the door, the key is at home, the lock is useful, and the key is also useful, but the two are separated by a door, so they cannot be combined.
The development of signal jammers is associated with the development of communication technology. With the emergence of new communication technologies, new signal frequency bands will appear accordingly. It is not possible to crack and avoid signal jammers through any number and band, because no matter which number or band you use, it is within its shielding range.